How to Troubleshoot ‘The Specified Domain Does Not Exist’ Error on Windows 10 PC

Updated March 2025: Stop these error messages and fix common problems with this tool. Get it now at this link

1. Download and install the software.
2. It will scan your computer for problems.
3. The tool will then fix the issues that were found.

Do you keep getting the ‘specified domain does not exist’ error on your Windows 10 PC? This can be a frustrating issue to deal with, but don’t worry – we are here to help! In this blog post, we will walk you through the steps that you can take to troubleshoot and fix this problem. We will also provide some tips on how to prevent it from happening in the future.

What causes the “Specified domain does not exist” error message?

The main reasons for this error are improperly configured network settings and poor network connection. Incorrectly configured or corrupt registers, system updates can also cause this error Specified domain either does not exist or could not be contacted Windows Error. Let’s look at each of the possible causes.

• Windows Update: One of the main causes for this error is a Pending or Failed Windows Update. A lot of times, users see this error because their computer has not been updated in a while. To fix this, you can try running the Windows Update troubleshooter or manually checking for updates.
• Bad network connection: Another possible cause of this error is a bad network connection. This can be due to a number of factors, such as a loose Ethernet cable, incorrect DNS settings, or an outdated network driver. To fix this, you can try restarting your computer and router/modem, checking your network settings, and updating your network drivers.
• Incorrectly configured registry keys: The registry is a critical part of the Windows operating system, and incorrect settings can cause a variety of problems. If you think that this might be the case, you can try running the Registry cleaner tool or manually editing the registry.
• Improperly configured network settings: If your network settings are not configured correctly, you may see the “Specified domain does not exist” error. To fix this, you can try resetting your network adapter or restoring your network settings to the default values.

These are just some of the possible causes for the “Specified domain does not exist” error message.

How to solve the “Specified domain does not exist” problem

Using a different DNS address 

We will configure the correct DNS address in the network settings on the client side. If you have recently upgraded your system, chances are your DNS settings have been reset. If you haven’t updated it, you should also check that the DNS address matches the domain controller’s address.

1. Go to the Start menu and open the Control Panel.
2. Now go to Network and Internet > Network Connections.
3. Right-click on your network connection and go to Properties.
4. To change your DNS, double-click Internet Protocol (TCP/IPv4).
5. Make sure that “Use the following DNS server address” is selected.
6. Finally, enter the DNS server address in the box and click OK.
7. Now you can connect without any problems or errors.



Disable IPv6 in the network settings

We will disable IPv6 in the network adapter properties and then run some commands to fix the error. Let’s see how to proceed.

1. Open the Control Panel.
2. Go to Network and Internet > Network and Sharing Center.
3. Now click on Change Card Settings on the left side.
4. Now disable the Internet Protocol (TCP/IPv6).
5. Now reboot the system.
6. After rebooting, open a command prompt and enter the following commands.
   • ipconfig /flushdns
   • ipconfig /share
   • ipconfig /renew
7. After running all the commands, reboot the system.
8. Finally, try to establish a connection.

Perform a system restore

It’s always a good idea to create a restore point in Windows 10 before you install new programs or make major changes to your settings. That way, if something goes wrong, you can use the restore point to go back to a working configuration. Here’s how to perform a system restore in Windows 10:

1. First, open the System Properties dialog by pressings the Windows key + R, typing sysdm.cpl, and pressing Enter.
2. Then, click on the System Protection tab and click the Configure button.
3. Select the drive you want to protect and click OK. Make sure the Turn on system protection option is selected and choose how much disk space you want to use for restore points. Then, click OK again.
4. To create a restore point, open the Control Panel and type Recovery in the search box. Click Create a restore point from the list of results.
5. On the System Protection tab, click Create. Type a name for your restore point and click Create again.

Change the registry key

Changing the value of the SysVolReady registry entry on the domain controller may solve this problem. Since this is a registry operation, it is recommended that you back up the registry or create a system restore point as a necessary precaution. You can then proceed as follows:

1. Press Win + R to open Run. Then type regedit and press Enter.
2. Go to the following path: HKEY_LOCAL_MACHINE\System\CurrentControlSet\ServicesNetlogonParameters.
3. In the right pane of the window, right-click the SysVolReaady entry and select Edit.
4. Under Value Data, change the value to 1 and click OK to save your changes.
5. Then restart your computer and see if the problem disappeared.

Perform an SFC scan

SFC scan is a process that can help to fix corrupt files on your computer. To run an SFC scan on Windows 10, follow these steps:

1. Open the Start menu and type “cmd” into the search box.
2. Right-click on the “Command Prompt” result and select “Run as administrator.”
3. Type the command “sfc /scannow” and press Enter.
4. The scan will now start and may take some time to complete.
5. Once the scan is finished, restart your computer and check for any improvements.

Start DISM

Windows 10 offers a number of ways to keep your PC running smoothly, and one of the most effective is the DISM scan. This tool can help to repair corrupt files and system settings, as well as improve performance by removing unnecessary files. Here’s how to run a DISM scan on Windows 10:

1. Press the Windows key + S to open the search box.
2. Type ‘Command Prompt’ into the search box and press Enter.
3. Type ‘DISM /Online /Cleanup-Image /RestoreHealth’ into the Command Prompt and press Enter.
4. The scan will now begin and could take several minutes to complete.
5. Once it’s finished, you’ll see a report on the results of the scan. If any problems were found, they’ll be listed and you can follow the instructions to fix them.

APPROVED: To fix Windows errors, click here.

Frequently Asked Questions